technical data sheet rpc-1.85 open circuit jack 08K12L-000S3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 fax : +49 8684 18-499 email : info@rosenberger.de page 1 / 3 rf_35/05.10/6.0 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg all dimensions are in mm; tolerances according to iso 2768 m-h interface according to iec 61169-32 mechanically compatible with rpc-2.40 documents application note an001 calibration services material and plating connector parts material plating center conductor beryllium copper gold, min. 1.27 m, over nickel outer conductor stainless steel passivated dielectric ps
technical data sheet rpc-1.85 open circuit jack 08K12L-000S3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 fax : +49 8684 18-499 email : info@rosenberger.de page 2 / 3 rf_35/05.10/6.0 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg electrical data frequency range dc to 70 ghz return loss 0.20 db, dc to 4 ghz 0.30 db, 4 ghz to 40 ghz 0.40 db, 40 ghz to 70 ghz error from nominal phase 1 2.0, dc to 4 ghz 5.0, 4 ghz to 40 ghz 8.0, 40 ghz to 70 ghz 1 the nominal phase is defined by the offset delay, the offset loss and the fringing capacitances mechanical data mating cycles 3 500 maximum torque 1.65 nm recommended torque 0.90 nm gauge 0.00 mm to 0.03 mm general standard definition for proper operation the vector network analyzer (v na) needs a model describing the electrical behavio ur of this calibration standard. the different models, units, and terms used will depend on the vna type and they will have to be entered into the vna. all values ar e based on typical geometry and plating. offset z o / impedance / z o 50 w offset delay 16.680 ps length (electrical) / offset length 5.00 mm offset loss 3.75 g ? /s loss 0.0109 db/ ghz fringing capacitances 2 2 fringing capacitances are determined individually for each open circuit and are documented in a calib ration certificate. environmental data operating temperature range 3 +20 c to +26 c rated temperature range of use 4 0 c to +50 c storage temperature range -40 c to +85 c rohs compliant 3 temperature range over which these specifications are valid. 4 this range is underneath and above the operating te mperature range, within the open circuit is fully functional and could be used without damage.
technical data sheet rpc-1.85 open circuit jack 08K12L-000S3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 fax : +49 8684 18-499 email : info@rosenberger.de page 3 / 3 rf_35/05.10/6.0 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg declaration of calibration options factory calibration standard delivery for this calibration standard inc ludes a factory calibration. the calibration certif icate issued reports individual calibration results, trac eable to national / international standards. model based standard definitions are individually optimized and reported in an agilent/keysight, rohde & schwarz a nd anritsu compatible vna format. accredited calibration not available. for further, more detailed information see applicat ion note an001 on the rosenberger homepage. calibration interval recommendation 12 months packing standard 1 pce in box weight 7.3 g/pce draft date approved date rev. engineering change n umber name date herbert babinger 26.08.04 martin moder 24.03.15 f0 0 14-1492 herbert babinger 24.03.15 while the information has been carefully compiled t o the best of our knowledge, nothing is intended as representation or warr anty on our part and no statement herein shall be construed as recommendati on to infringe existing patents. in the effort to i mprove our products, we reserve the right to make changes judg ed to be necessary.
|
